An a Review on 3-D Analysis of Building Frame

Using STAAD-PRO Softwear

Abhishek Singh #1, Honey Gaur *2
#1
Research scholar, Department of Civil Engineering, Kalinga University, Raipur
*2
Asst. Professor, Department of Civil Engineering, Kalinga University, Raipur
st  Reading the result take place in POST
Abstract— This In 21 century due to large
PROCESSING Mode.
population the no of areas in units are decreasing
 First we choose the output file that we want to
day by day. Few years back the populations were
analyze (like various loads or load combination)
not so vast so they used to stay in Horizontal
.Then it will show the results.
system(due to more area available per person).But
4. Send the analysis result to steel design or concrete
now a day’s people preferring Vertical System(high
design engines for designing purpose.
rise building due to shortage of area).In high rise
buildings we should concern about all the forces that  If someone wants to do design after analysis then he
act on a building ,its own weight as well as the soil can ask STAAD-PRO to take the analysis results to
bearing capacity .For external forces that act on the be designed as design
building the beam, column and reinforcement  The data like Fy main, Fc will assign to the view
should be good enough to counteract these forces  Then adding design beam and design column.
successfully. A capacity of the soil should be good
enough to pass the load successfully to the  Running the analysis it will show the full design
foundation. For loose soil we preferred deep structure.
foundation (pile).If we will do so much calculation II. LITERATURE REVIEW
for a high rise building manually then it will take
more time as well as human errors can be occurred. Following are the literature reviews are based on the study.
Viviane Warnotte are summarized the basic concepts on
So the use of STAAD-PRO will make it easy.
which the seismic pounding effect Occurs between
Keywords— Software Analysis, High rise Building, STADD
PRO 3D. adjacent buildings. He identified the conditions under
which the seismic Pounding will occur between
I. INTRODUCTION buildings and adequate information and, perhaps more
STAAD-PRO software was born giant. It is the most Importantly, pounding situation analyzed. From his
common and popular software used now days. Basically it is research it was found that a elastic model cannot predict
performing design works. There are following four steps correctly the behaviors of the structure due to seismic
using STAAD-PRO to reach the goal. pounding. Therefore non-elastic analysis is to be done to
•Firstly Prepare the input file. predict the required seismic gap between buildings.
Shehata E. Abdel Raheem are to be developed and
•Second Analyze the input file.
implemented a tool for the inelastic analysis of seismic
•Third Watch the results and verify them.
pounding effect between buildings. They carried out a
•Fourth Send the analysis result to steel design or
parametric study on buildings pounding response as well as
concrete design engines for designing purpose. proper seismic hazard mitigation practice for adjacent
buildings. Three categories of recorded earthquake
1. Prepare the input file-
excitation were used for input. He studied the effect of
 First of all we described the structure. In description impact using linear and nonlinear contact force model for
part we include geometry, the materials, cross different separation distances and compared with nominal
sections, the support conditions. model without pounding consideration.
2. Analyze the input file-We should sure that we are Robert Jankowski are to be addressed the fundamental
using STAAD-PRO syntax. Else it will error. questions concerning the application of the nonlinear
 We should sure that all that we are inputting that will analysis and its feasibility and limitations in predicting
generate a stable structure .Else it will show error. Seismic pounding gap between buildings. In his analysis,
 At last we should verify our output data to make sure elastoplastic multi-degree of freedom. Lumped a mass
that the input data was given correctly. models are used to simulate the structural behavior and a
3. Watch the results and verify them. non-linear viscoelastic impact elements are applied to
model collisions. The results of the study Prove that

1
 pounding may have considerable influence on behavior of
the structures.

 At least 20% of the concrete shall be residual

products used as aggregate.
 Use of concrete industries own residual products.
 Use of new types of residual products, previously
land filled or disposed of in others ways.
 CO2- neutral, waste-derived fuels shall substitute
fossil fuels in the cement production by at least 10%.

III. CONCLUSION
For column of the area of steel or percentage of steel always
greater than required for wind load combination than the
seismic load combination.

References
1) “Review On Ground Granulated Blast-Furnace Slag as a
supplementary cementious Material”
Sagar R.Raut, P.P.Saklecha, R.S.Kedar, International
conference on Quality Up-gradation in Engineering, Science
and Technology (ICQUEST2015)
2) “Analysis Of Strength Characteristics Of GGBS Concrete”
Vinayak Awasare, Prof. M. V. Nagendra, International Journal
of Advance Engineering Technology (E-ISSN 0976-3945)
3) “An Investigation Of Current Status Of “Green” Concrete
In The Construction Industry”
Ruoyu Jin and Qian Chen, 49th ASC Annual International
Conference Proceedings, 2013
4) “Development of Green Concrete and Assessment of its
Strength Parameters”
Shailendra Tiwari, Sudhir Nigam, Dharmendra Kumar and
Abhinav Nangias, International Journal of Engineering and
Technical Research (IJETR) ISSN:2321-0869, volume -3
5) “Durability of concretes containing ground granulated blast
furnace GGBS against sulphate attack”
A.A. Ramezanianpour, S. Atarodi , M. Sami, Third
International Conference Materials and Technologies
6) “Effects of manufactured sand on compressive strength
and workability of concrete.”
Nimitha Vijayaraghavan and A S Wayal, International Journal
of Structural and Civil Engineering Research (ISSN 2319-
6009) Vol. 2, No. 4, November 2013
7) “Effect of silica fume on strength and durability parameters
of concrete.”
N. K. Amudhavalli, Jeena Mathew, International Journal of
Engineering Science and Emerging Technologies (ISSN:
2231-6604), August 2012
8) “International Journal of civil and structural engineering.”
Shankar H. Sanni, R. B. Khadiranaikar 2012 volume 3, No 2.
9 ) “ Green concrete: efficient and eco-friendly construction
materials”
Chirag Garg and Akash Jain , International journal of research
in engineering and technology (IMPACT:IJRET) Vol.2 Issue 2
Feb 2014 ,259-264.